EquipmentHow-tosPublished

How to calculate cost per print before you buy a machine

Ink, maintenance, labour, downtime and the finance payment. The formula, worked through, plus the numbers salespeople leave out.

  • 9 min read
  • 1,150 words
How to calculate cost per print before you buy a machine — pricing calc at a print shop
Equipment9 min readA1printsoft EditorialPhoto: Jakub Żerdzicki / Unsplash
On this page5 sections

The short answer

  • Cost per print = (fixed monthly costs ÷ prints per month) + variable cost per print
  • Include the finance payment, maintenance, and the space the machine occupies
  • Assume 5% downtime — machines do not run every scheduled hour
  • Run the numbers at your realistic volume, not the dealer's optimistic one
  • The break-even volume matters more than the headline cost per print

Every equipment quote comes with a cost-per-print figure attached. It is almost always calculated at a volume you will not hit, using an ink cost that assumes ideal coverage, and excluding the finance payment on the machine itself. That is not necessarily dishonest — a dealer has to pick some assumptions — but the assumptions chosen are the flattering ones, and the number that results has very little to do with what the machine will cost you.

You can calculate a real figure in about twenty minutes. It requires no specialist knowledge, only a willingness to be pessimistic about volume and honest about downtime. What follows is the formula, a worked example, and the specific line items that go missing.

What is the formula?

Cost per print

(fixed monthly costs ÷ prints per month) + variable cost per print

Fixed monthly costs are everything you pay whether the machine runs or not — the finance or lease payment, any service contract, insurance, and a fair allocation of the floor space it occupies. Space is the one people leave out, and it is real. A machine with its curing equipment and working area occupies square footage you are paying rent on, and that footage is not available for anything else.

Variable costs are what each print consumes: ink or film, pretreat, consumables, the electricity to cure, and the operator's time. Operator time is the largest variable cost on most digital machines and the one most often omitted from dealer figures, on the grounds that you were paying that person anyway. You were, but their hour is finite, and an hour spent at this machine is an hour not spent elsewhere.

A worked example

A $28,000 machine, financed over five years, in a shop expecting 1,400 prints a month:

Fixed, monthly
Finance payment$540
Service contract$180
Insurance$35
Floor space (60 sq ft)$90
Total fixed$845
Variable, per print
Ink$1.10
Pretreat$0.32
Consumables$0.14
Power$0.06
Operator (90 sec at $26/hr)$0.65
Total variable$2.27

At 1,400 prints: $845 ÷ 1,400 = $0.60, plus $2.27 = $2.87 per print. Now run it again at 700 prints a month, which is a perfectly plausible outcome in a first year: $845 ÷ 700 = $1.21, plus $2.27 = $3.48 per print. That is twenty-one per cent higher, and it comes entirely from the fixed costs having half as many prints to spread across.

The variable cost has not moved at all. This is why volume assumptions matter more than any other input. A dealer quoting $2.40 at 2,500 prints a month is not wrong about the arithmetic — they are optimistic about the denominator. Always calculate at the volume you actually expect, then calculate again at half of it to see how much pain a slow year would cause.

The cost per print on the quote is a function of a volume you have not proved yet.

What gets left out?

Downtime. Machines do not run every hour they are scheduled to. Head cleaning, colour changes, jams, maintenance and waiting on a delivery all take time — assume five per cent minimum, and more in the first six months. Downtime does not add a line to your costs; it reduces the denominator, which raises cost per print without anything appearing to change.

Learning curve. The first two to three months produce more spoilage, slower cycle times and more reprints than the steady state. Budget for it explicitly instead of being surprised by it. Waste follows the same logic: test prints, misprints and garments ruined during setup run two to four per cent on digital work, and it comes out of your margin either way.

Ink at real coverage. Dealer ink figures usually assume a modest print on a light garment. A full-front print on a dark garment needing a white underbase can use two to three times as much ink. If your typical work is dark garments, use the dark garment figure, and check it against the per-print costs in the DTG and DTF comparison rather than the brochure.

The operator. Discussed above, and worth repeating because it is the single largest omission. If the dealer's number does not include labour, it is not a cost per print. It is a cost of materials.

What is your break-even?

The more useful question is not what a print costs, but how many prints you need before the machine pays for itself against your current alternative — usually outsourcing.

Prints / monthCost per printvs outsourcing at $4.20
400$4.38Losing $0.18
700$3.48Saving $0.72
1,400$2.87Saving $1.33
2,500$2.61Saving $1.59

Break-even here is a little over 400 prints a month. Below that, outsourcing is cheaper and you have avoided a five-year commitment. Notice too that the gain between 1,400 and 2,500 is much smaller than the gain between 400 and 1,400.

Fixed costs stop mattering once they are thinly enough spread, and past that point the machine's economics barely improve. Knowing where that flattening happens tells you when a second machine makes more sense than pushing the first one harder. The same method applied to screens and press time gives you the equivalent picture for a screen print job, where the fixed block is makeready rather than finance.

What should you ask the dealer?

Six questions

  • "At what monthly volume is your cost-per-print figure calculated?"
  • "Does it include labour? If not, give me the figure with labour."
  • "What ink coverage does it assume — light garment or dark with underbase?"
  • "What is the expected maintenance cost in years three, four and five?"
  • "What is the current lead time on the parts that fail most often?"
  • "Give me a customer running this at my volume, not at your best customer's volume."

The maintenance question separates a considered quote from a hopeful one. Year-one running costs are on every spec sheet. Years three to five are where machines get expensive, and a dealer who can answer that question in specifics is one who has supported these machines through their full life rather than only sold them.

That last question is the same one worth asking any software vendor, and for the same reason — a reference chosen for you is a reference chosen to flatter. The full set of questions a demo will not answer transfers almost directly to a showroom floor. The rest of the equipment archive assumes you are buying on arithmetic rather than on the day.

Filed underEquipmentHow-tos
Share
Written byA1printsoft Editorial
175 articles

The print production desk at A1Printsoft. Writes the practical side of running a decorating shop: what things cost, how long they take and what to charge, checked against published trade figures.

Keep reading

More on equipment

All Equipment articles

Set up in an afternoon. From what you already do.

Free for 14 days · no card · pick what you make and we preload the methods, products and price tables.