ProductionPublished

Plastisol or water-based: choosing ink per job

Plastisol cures in 20–60 seconds at 320°F. Water-based needs closer to three minutes and a dryer that can deliver it. Which to use, and what each demands of your shop.

  • 9 min read
  • 1,314 words
Plastisol or water-based: choosing ink per job — screen print at a print shop
Production9 min readA1printsoft EditorialPhoto: Đồng Phục Hải Triều / Unsplash
On this page6 sections

The short answer

  • Plastisol cures in 20–60 seconds above roughly 320°F (160°C)
  • Water-based must first evaporate water, then cross-link — around three minutes
  • Water-based gives a far softer hand; plastisol gives brighter opacity on darks
  • Your dryer decides this more often than your preference does
  • Plastisol tolerates sitting on the screen. Water-based does not

Ink choice gets discussed as a matter of taste, and it mostly is not. It is a question about your dryer, your press discipline and what the customer will do with the garment. A shop that picks by preference rather than by those three things will eventually produce a batch that fails, and the failure will arrive weeks later at the customer rather than in the shop where it could be caught.

The two families behave differently in ways that matter operationally, not just aesthetically. Understanding the cure chemistry is the shortest route to knowing which jobs you can take.

How does each one actually cure?

Plastisol is PVC particles suspended in plasticiser. It does not dry — it has no water or solvent to lose — so it will sit wet on a screen indefinitely and only changes state when heated. Cure happens when the whole ink film reaches roughly 320°F (160°C), at which point the particles fuse. In practice that is 20 to 60 seconds in a conveyor dryer, with the standard working range quoted between 300 and 330°F.

Water-based ink cures in two stages, and this is the crucial difference. First the water has to evaporate, then the binder cross-links with heat. Both stages need time, so a water-based print typically wants around three minutes of dryer time against plastisol's one, at a similar or slightly higher temperature.

That single fact governs almost everything downstream. A dryer sized for plastisol at a given belt speed cannot simply run water-based at the same speed. Slowing the belt to a third of its rate cuts your throughput to a third, which is a production decision rather than an ink decision.

Plastisol asks your dryer for temperature. Water-based asks it for time, and time is throughput.

What does the customer actually feel?

Water-based ink soaks into the fibre and becomes part of the fabric. The result is a print you can barely feel, breathable, with the garment's texture still visible through it. This is why water-based dominates retail and fashion work, where the buyer picks the garment up and judges it by hand before deciding.

Plastisol sits on top of the fabric as a film. On a dark garment that is an advantage — the opacity is excellent and colours stay bright without heroic effort. On a large print it is a drawback, because a full-front plastisol block is a sheet of plastic on the shirt, and on a lightweight tee the customer notices how it drapes and how warm it is.

There is an environmental dimension that increasingly appears in procurement conversations. Water-based inks are free of PVC and phthalates, which matters to corporate buyers whose reporting now covers this. If you run company store programmes, expect to be asked, and expect the answer to be part of the decision rather than a footnote.

What does your dryer allow?

This is the constraint that settles most shops' answer, and it is worth being honest about before promising a customer anything.

PlastisolWater-based
Cure temperature~300–330°Fsimilar, often a little higher
Dwell time20–60 secondsaround 3 minutes
Mechanismfuse on heatevaporate, then cross-link
Effect on throughputbaselineroughly a third of it

A short flash-cure unit or a small conveyor sized for plastisol will not properly cure water-based ink, and the failure is invisible on the day. The print looks fine, feels fine, and comes apart in the wash — which is the worst kind of production fault, because it reaches the customer with your name on it.

Before quoting water-based work, run a wash test with your actual dryer at your actual belt speed. Print a sample, cure it, wash it ten times, and look at it. That is a morning's work once, and it tells you whether water-based is a service you can genuinely offer or one you are hoping will be fine.

How do they behave on the press?

Plastisol is forgiving in exactly the way a busy shop needs. It will not dry in the mesh, so a press can sit through a phone call, a lunch break or a screen change without anything seizing up. For a shop running many short jobs with frequent interruptions, that tolerance is worth a great deal.

Water-based ink contains water, and water evaporates. Left on a screen it will dry in the mesh and block it, and recovering a blocked screen mid-run costs more time than the job was worth. Running water-based means keeping the ink moving, misting screens during pauses, and treating an unattended press as a problem rather than a pause.

That has a scheduling consequence people underestimate. Water-based work wants to be run as a continuous block, not slotted between other jobs. If your day is a series of interruptions — and in most shops it is — batching water-based jobs onto specific days is far more practical than treating the two inks as interchangeable within a shift.

Press discipline for water-based

  • Keep ink moving; flood the screen during any pause
  • Mist screens if the press stops for more than a minute or two
  • Batch water-based jobs together rather than interleaving them
  • Reclaim promptly — dried water-based ink is far harder to remove
  • Confirm cure with a wash test on a new garment type, not by eye

Which one for which order?

OrderChooseBecause
Dark garments, bold graphicPlastisolOpacity without fighting for it
Retail line, soft hand requiredWater-basedThe buyer judges by touch
Large full-front on lightweight teeWater-basedPlastisol block changes the drape
Short run between other jobsPlastisolTolerates interruption
Corporate programme with an eco requirementWater-basedNo PVC or phthalates
Tight deadline, dryer at capacityPlastisolThree times the throughput

Notice that two of those rows are about your shop rather than the print. That is deliberate — ink choice is a scheduling decision as much as an aesthetic one, and pretending otherwise is how a shop ends up promising a soft-hand retail run on a week when the dryer is already the bottleneck.

Quantity does not appear in that table, because both inks work across the range. What changes with quantity is whether screen printing is the right process at all: below roughly a dozen pieces, a digital process is usually cheaper and faster, and the ink question does not arise.

Should you run both?

Most established shops do, and the reason is commercial rather than technical. Plastisol covers the bulk of everyday work — clubs, events, workwear, anything on darks — while water-based opens retail and fashion accounts that will not accept a plastisol hand. Turning that work away is turning away the higher-margin end of the market.

What running both actually requires is separation. Different inks, different additives, different reclaim chemistry, and ideally different days. Shops that try to run them interchangeably within a shift tend to get the worst of each: plastisol jobs slowed by a belt set for water-based, and water-based jobs drying in the mesh during a plastisol changeover.

If you are considering the move to water-based, cost it properly before committing. The ink is more expensive per unit, the throughput hit is real, and the dryer may need replacing — which makes it an equipment decision, not a materials one. The method for working that out is the same as any other: fixed costs divided by realistic volume, plus the variable per print, with the throughput change reflected in the volume. The rest of the production archive assumes you have tested cure rather than assumed it.

Filed underProduction
Share
Written byA1printsoft Editorial
175 articles

The print production desk at A1Printsoft. Writes the practical side of running a decorating shop: what things cost, how long they take and what to charge, checked against published trade figures.

Keep reading

More on production

All Production articles

Set up in an afternoon. From what you already do.

Free for 14 days · no card · pick what you make and we preload the methods, products and price tables.