EquipmentPublished

Film output and RIP software

A screen can only be as good as the film that exposed it. Density, resolution and the settings that decide whether halftones survive.

  • 12 min read
  • 1,016 words
Film output and RIP software — software tech at a print shop
Equipment12 min readA1printsoft EditorialPhoto: 1981 Digital / Unsplash
On this page7 sections

The short answer

  • Film must block UV completely — opacity beats resolution
  • Grey or thin black areas expose through and ruin the stencil
  • A RIP controls ink laydown, halftone angle and frequency properly
  • Halftone frequency must suit your mesh, not the artwork
  • Most exposure problems are film problems

The film positive is the first physical step in screen printing and the one most often treated casually. A screen exposed through inadequate film cannot produce a sharp print, and no adjustment further down the line recovers what was lost at the start.

What the film has to do

One job: block ultraviolet light completely where the ink should pass, and let it through everywhere else. Everything about film output serves that.

A good positive has

  • Solid, genuinely opaque black in the image areas
  • Clear film everywhere else
  • Sharp edges without spread or feathering
  • Halftone dots that are round and separate
  • Registration marks, on every colour
  • Flatness — a curled film lifts off the screen

Contact is as important as opacity. Film that does not sit tight against the emulsion allows light to creep under the edges, which softens detail regardless of how good the print itself was.

Hold the film to a light. If you can see through the black, so can your exposure unit.

Density

Density is the measure of how completely the black blocks light, and it is the single most important property of a film positive.

SymptomCause
Stencil hardening in image areasInsufficient density
Halftone dots partly exposedThin dots on the film
Fine detail lost after washoutLight creeping through
Ink spreading beyond the lineFeathered film edges
Blotchy black on the filmInk laydown or film type

Shops fight these by extending exposure, which makes it worse — longer exposure hardens more emulsion under thin blacks. The fix is denser film, not more light, and that distinction saves a great deal of frustration at the exposure unit.

Printers

TypeDensityNotes
Inkjet with dye inkPoorNot suitable
Inkjet with pigment inkGoodThe common choice
Dedicated film printerExcellentBuilt for the job
Laser on filmVariableToner density is inconsistent
ImagesetterExcellentRare; high volume only

Use waterproof inkjet film matched to your ink, not any transparency. Film and ink are designed as a pair, and mismatching them produces exactly the blotchy, thin blacks that cause exposure faults.

Dedicated all-black systems are worth the cost in any shop making screens daily. They lay more ink, dry predictably, and remove the persistent battle to get density from a general-purpose printer.

What a RIP adds

A RIP — raster image processor — sits between the artwork and the printer and controls how the image is rendered. Printing from a design application to a printer driver gives you almost none of that control.

What it gives you

  • Control over ink laydown, so blacks are genuinely dense
  • Halftone frequency, angle and dot shape you choose
  • Separations output as individual films
  • Registration marks added automatically
  • Consistent, repeatable output between jobs
  • Multiple designs ganged onto one sheet

Halftone control is the reason most shops buy one. A printer driver applies its own screening designed for photographs, which is not what a screen printing halftone needs, and the results are unpredictable — a real obstacle to simulated process work.

Ganging pays for itself on film costs alone in a busy shop, since several small designs on one sheet is a saving on every job rather than an occasional one.

Halftone settings

Halftone frequency must be chosen for the mesh that will hold it, not for the artwork's apparent detail. Too fine and the dots fall through the mesh openings; too coarse and the pattern becomes visible in the print.

What to settle

  • Frequency, matched to your mesh count
  • Angle, to avoid moiré against the mesh
  • Dot shape — elliptical dots hold better through midtones
  • The smallest dot your process reliably holds
  • The largest dot before it fills solid

Test your own limits rather than adopting published figures. Every combination of mesh, emulsion, exposure and press has a different usable range, and knowing yours is what lets you promise tonal work confidently.

Handling and storage

Films last if you let them

  • Let the ink dry fully before stacking
  • Store flat — curl prevents contact
  • Keep out of direct light and away from heat
  • Handle by the edges; fingerprints affect density
  • Label with the job, colour and date
  • File by customer so a repeat needs no reprint

Keeping films for repeat customers is straightforward economy. A reorder that reuses existing film skips output entirely, which is part of what makes a repeat run so much more profitable than a first one.

Diagnosing problems

When a screen exposes badly, check the film before adjusting anything else. It is the most likely cause and the easiest to rule out.

In order

  • Hold the film to a bright light — can you see through the black?
  • Check it sat flat against the glass during exposure
  • Look at the halftone dots under magnification
  • Check the emulsion coating was even and fully dry
  • Only then change exposure time
  • Only then suspect the emulsion or the unit

Keep a known-good reference film for testing. A simple positive with solid areas, fine lines and a halftone gradient, output when everything was working, gives you something to expose against when results drift — and it separates a printer problem from an emulsion or exposure problem in a single test.

Check the printer itself periodically. Inkjet heads clog, ink settles and output density falls gradually rather than suddenly, so film that was dense enough six months ago may not be now — and nothing about the artwork or the exposure will have changed to explain it.

That order matters because exposure time is the easiest thing to change and the least likely to be wrong. Shops that start there end up with an exposure setting tuned around a film problem, and every subsequent screen inherits the compromise. The rest of the equipment archive assumes the film was checked before the exposure was adjusted.

Filed underEquipment
Share
Written byA1printsoft Editorial
175 articles

The print production desk at A1Printsoft. Writes the practical side of running a decorating shop: what things cost, how long they take and what to charge, checked against published trade figures.

Keep reading

More on equipment

All Equipment articles

Set up in an afternoon. From what you already do.

Free for 14 days · no card · pick what you make and we preload the methods, products and price tables.