The short answer
- A flash gels ink so the next colour sits on top instead of mixing in — it does not cure it
- Every flash adds a station and a dwell, which can halve your press speed
- Wet on wet avoids flashing entirely and works for many colour combinations
- A white underbase on a dark garment almost always needs a flash
- Sequencing light to dark removes flashes you thought you needed
Flash curing is the difference between a multi-colour job running smoothly and one that takes twice as long as quoted. It is also one of the least understood steps in screen printing, partly because the word "cure" is misleading — a flash does not cure anything.
What does a flash actually do?
It applies enough heat to gel the surface of the ink: hardening it just enough that the next screen can print on top without picking the wet ink up into its mesh. The ink underneath is still uncured and will only be fully cured in the dryer at the end.
That distinction matters practically. A flash is not a substitute for the dryer, and a garment that has only been flashed is not finished. Shops occasionally cut the dryer pass on a heavily flashed job and produce prints that fail on the third wash — which is the classic undercure that only a wash test catches.
It also means a flash can be overdone. Too much heat gels the ink hard, which stops the next colour bonding properly and produces a print where one colour lifts from the one beneath.
The cost of flashing
Flashing is expensive in press time and shops rarely account for it when quoting.
| Cost | Effect |
|---|---|
| A station occupied | One fewer print head available |
| Dwell time | The whole press waits for the slowest step |
| A cooling station | Often needed after, occupying another position |
| Heat on the platen | Platens warm up and affect registration |
| Operator attention | Flash timing has to be watched |
The dwell is the one that governs throughput. A carousel moves at the speed of its slowest station, so a three-second flash sets the pace for every station regardless of how fast the printing itself is. A job with two flashes can run at half the rate of the same job with none.
That belongs in your job costing. A four-colour design with two flashes is not the same production job as a four-colour design without, and pricing them identically underprices the first.
A carousel runs at the speed of its slowest station, and that station is almost always the flash.
Wet on wet
Printing each colour directly onto the previous one without flashing between. It is faster, it is easier on the garment, and it works more often than shops assume.
It succeeds when the colours do not need to be fully opaque over one another, and when the design does not have large solid areas overlapping. Adjacent colours that touch but do not overlap are ideal — there is nothing to mix.
Wet on wet works when
- Colours are adjacent rather than heavily overlapping
- You print light to dark, so any pickup is less visible
- The garment is light and no underbase is needed
- Ink viscosity is consistent between colours
- Mesh counts are chosen so later colours deposit less
Mesh selection is the technique that makes it work. Printing later colours through a higher mesh lays down less ink, reducing what there is to pick up — which is why the same design can be wet-on-wet in one shop and require flashing in another.
When you must flash
Some situations genuinely require it, and trying to avoid them produces a worse print rather than a faster one.
| Situation | Why |
|---|---|
| White underbase on a dark garment | Colours must sit on solid, gelled white |
| Light colour over dark | Any pickup is immediately visible |
| Heavy solid areas overlapping | Too much wet ink to print onto |
| Halftones over a solid | Dots fill in if the base is wet |
| Specialty inks — puff, metallic | Behave differently, usually need gelling |
The underbase case is effectively universal. Any design printed on a dark garment with a white base needs that base gelled before colours go over it, and no amount of sequencing avoids it.
Setting the flash up
Under-flashing leaves ink that picks up; over-flashing gels it too hard and can scorch the garment. The window is narrower than people expect and it changes with the garment.
Getting it right
- Set height and dwell on the actual garment, not a test scrap
- Test by touching the flashed ink — tacky is under, dry to the touch is about right
- Watch for scorching on synthetics and light colours
- Add a cooling station after the flash if platens are heating up
- Re-check after twenty or thirty pieces — platens warm through a run
- Reset when the garment weight changes
The platen warming point is the one that causes mid-run problems. Settings correct on the first garment can be over-flashing by the fiftieth, because the platen itself has absorbed heat. If registration drifts or colours start lifting partway through a run, that is usually why.
Sequencing to avoid a flash
Print order is a design decision as much as a production one, and choosing it well removes flashes.
Light to dark is the general rule on light garments. Any pickup from a lighter ink into a darker screen is far less visible than the reverse, so a sequence running pale colours first frequently needs no flash at all.
Separate the overlaps. If two solid colours overlap heavily, ask whether the artwork needs them to. A trap or a knockout in the separation can remove the overlap entirely, which removes the reason to flash.
Reconsider the process. A design needing three flashes on a twelve-piece run is a job spending most of its press time waiting. That is frequently a job for a digital process instead, where colour count and overlap cost nothing.
Decide the sequence at separation rather than at the press. Working it out with screens already loaded costs setup time and usually produces a compromise, whereas planning it takes minutes and can remove a station from the job. The rest of the equipment archive assumes flashes are planned rather than discovered.



