EquipmentHow-tosPublished

Screen reclaim, chemicals and the washout area

Reclaim is fifteen minutes a screen and the least popular job in the shop. How to make it fast, safe and repeatable — and why ghost images happen.

  • 11 min read
  • 1,012 words
Screen reclaim, chemicals and the washout area — screen print at a print shop
Equipment11 min readA1printsoft EditorialPhoto: Anthony Roberts / Unsplash
On this page6 sections

The short answer

  • Reclaim is four steps: ink removal, emulsion stripping, degreasing, drying
  • Budget 15–20 minutes a screen plus chemistry, and cost it into the job
  • Ghost images are haze, not emulsion — they need a separate remover
  • Degreasing is the step people skip and the reason emulsion later fails to adhere
  • Ventilation, eye protection and a proper trap are not optional

Reclaim is the least glamorous part of screen printing and the part that quietly determines print quality. A screen reclaimed properly coats evenly, holds detail and lasts for years. One reclaimed carelessly develops haze, fails to hold emulsion, and gets blamed for problems that appear much later at the press.

It is also a real cost that belongs in the job rather than in general overhead — the screen needs reclaiming because that job ran.

The four steps

StepRemovesSkipping it causes
1. Ink removalInk from mesh and frameInk contaminating the stripper
2. Emulsion strippingThe hardened stencilEmulsion left in the mesh
3. DegreasingOils, residue, fingerprintsEmulsion not adhering next time
4. DryingWaterEmulsion coating unevenly

Do them in order and do not combine them. The commonest shortcut is stripping emulsion without removing ink first, which contaminates the stripper, wastes chemistry and leaves residue that has to be dealt with anyway.

Degreasing is the step most often skipped, because the screen looks clean without it. It is not — handling leaves oils that prevent emulsion adhering properly, and the failure appears at the next exposure as emulsion breaking down during the wash-out. That gets diagnosed as an exposure problem, and it is not.

Ghost images

A faint outline of a previous design that remains after all the emulsion has gone. It is not emulsion and no amount of stripper will shift it.

Two distinct causes. Stain is pigment sitting in the mesh — cosmetic, and it does not affect printing. Haze is emulsion or ink residue bonded into the mesh weave, and it does affect printing, because it partially blocks the openings and reduces ink flow in that area.

Haze needs a dedicated haze remover, used after stripping and before degreasing, and it is aggressive stuff — follow the dwell time rather than leaving it longer, because extended contact degrades the mesh. If you find yourself hazing every screen, the cause is usually emulsion left too long before reclaim or ink allowed to dry in the mesh.

A screen that looks clean and prints badly is usually hazed, not underexposed.

Setting up the area

Reclaim produces water, chemicals and residue, and all three are hostile to the rest of the shop. Give it its own space with proper services — this is one of the few genuine must-be-separate zones.

What the washout area needs

  • A backlit washout booth — you cannot judge a screen you cannot see through
  • Pressure washer or a high-pressure hose, with a regulator
  • Drainage with a filtration trap — emulsion must not enter the drain
  • Ventilation, particularly for haze remover
  • Eye protection and gloves, kept at the booth
  • A drying rack out of the spray zone
  • An eyewash station

The trap is a legal as well as a practical matter in most places. Emulsion and ink residue entering the drain is a discharge issue, and the fine for it is considerably more than the trap. Check your local requirements rather than assuming.

Backlighting the booth is the single change that most improves reclaim quality. Held against light, a screen shows haze, residual emulsion and pinholes immediately; in ordinary light it looks fine and reveals its problems at exposure.

Chemical handling

Reclaim chemistry is the most hazardous material most decorating shops handle, and familiarity makes people casual with it.

Non-negotiable

  • Eye protection whenever spraying or applying — pressure atomises everything
  • Chemical-resistant gloves, replaced when they degrade
  • Ventilation running, not just present
  • Never mix products, and rinse thoroughly between steps
  • Safety data sheets accessible, not filed somewhere
  • Original labelled containers — never decanted into unmarked bottles
  • Everyone who reclaims trained, including anyone covering

The mixing rule matters most. Haze removers and strippers are chemically different and combining them can produce a genuine hazard, which is why rinsing between steps is a safety measure rather than a thoroughness one.

The training line matters because reclaim is the job that gets handed to whoever is free. Anyone who might do it needs to have been shown, and that belongs in the first-week induction rather than being picked up.

Screen life

Mesh does not last forever. Every reclaim cycle abrades it slightly, tension drops over time, and a screen that has lost tension prints poorly no matter how well it is prepared.

SymptomUsually means
Registration will not holdTension has dropped
Print looks soft on a fine meshMesh abraded or hazed
Emulsion coating unevenlyDegreasing skipped, or mesh damaged
Pinholes appearing repeatedlyMesh damage; retension or replace

Check tension periodically rather than waiting for print quality to tell you. A tension meter is inexpensive against the press time wasted fighting a slack screen, and it turns "this screen is awkward" into a measurement anyone can act on.

Making it not the worst job in the shop

Reclaim is disliked because it is wet, chemical and usually done at the end of a long day. Three changes help more than anything else.

Reclaim promptly. Screens left for days are dramatically harder — ink dries in the mesh and emulsion becomes stubborn. Same-day reclaim is faster per screen than batching, even though batching feels more efficient.

Batch by chemistry, not by time. Strip several screens together so the chemistry has dwell time while you work on the next, rather than standing waiting on each one.

Make it a scheduled job. Reclaim that happens when someone has a gap does not happen. On the board as a task with a name against it, it does — and it stops competing with production it will always lose to. The rest of the equipment archive assumes screens are reclaimed the day they come off the press.

Filed underEquipmentHow-tos
Share
Written byA1printsoft Editorial
175 articles

The print production desk at A1Printsoft. Writes the practical side of running a decorating shop: what things cost, how long they take and what to charge, checked against published trade figures.

Keep reading

More on equipment

All Equipment articles

Set up in an afternoon. From what you already do.

Free for 14 days · no card · pick what you make and we preload the methods, products and price tables.